Tugas 5 Jarkom III - ACL

Rancangan ACL pada paket tracer

SETINGAN PADA ROUTER O
— System Configuration Dialog —
Continue with configuration dialog? [yes/no]: NO
Press RETURN to get started!
Router>ENA
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.10.1 255.255.255.0
Router(config-if)#no sh
/0, changed state to up
Router(config-if)#int fa1/0
Router(config-if)#ip add 172.16.20.1 255.255.255.0
Router(config-if)#no sh
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
Router(config-if)#int se2/0
Router(config-if)#ip add 172.16.30.1 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no sh
%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#router ospf 100
Router(config-router)#network 172.16.30.1 0.0.0.255 area 0
Router(config-router)#network 172.16.30.0 0.0.0.255 area 0
Router(config-router)#network 172.16.20.0 0.0.0.255 area 0
Router(config-router)#network 172.16.10.0 0.0.0.255 area 0
Router(config-router)#exit
Router(config)#access-list 20 permit host 172.16.10.5
Router(config)#line vty 0 4
Router(config-line)#access-class 20 in
Router(config-line)#exit
Router(config)#copy run start
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]

Router 0

SETINGAN PADA ROUTER 1
— System Configuration Dialog —
Continue with configuration dialog? [yes/no]: NO
Press RETURN to get started!
Router>ENA
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.10.1 255.255.255.0
Router(config-if)#no sh
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#int fa1/0
Router(config-if)#ip add 172.16.20.1 255.255.255.0
Router(config-if)#no sh
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
Router(config-if)#int se2/0
Router(config-if)#ip add 172.16.30.1 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no sh
%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#router ospf 100
Router(config-router)#network 172.16.30.1 0.0.0.255 area 0
Router(config-router)#network 172.16.30.0 0.0.0.255 area 0
Router(config-router)#network 172.16.20.0 0.0.0.255 area 0
Router(config-router)#network 172.16.10.0 0.0.0.255 area 0
Router(config-router)#exit
Router(config)#access-list 20 permit host 172.16.10.5
Router(config)#line vty 0 4
Router(config-line)#access-class 20 in
Router(config-line)#exit
Router(config)#copy run start
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]

Router 1

SETINGAN PADA ROUTER 2
Continue with configuration dialog? [yes/no]: no
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int se 3/0
Router(config-if)#ip add 172.16.60.2 255.255.255.0
Router(config-if)#no sh
%LINK-5-CHANGED: Interface Serial3/0, changed state to up
Router(config-if)#exit
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0, changed state to up
Router(config)#int fa1/0
Router(config-if)#ip add 172.16.80.1 255.255.255.0
Router(config-if)#no sh
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
Router(config-if)#ex
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.70.1 255.255.255.0
Router(config-if)#no sh
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#ex
Router(config)#router ospf 100
Router(config-router)#network 172.16.60.0 0.0.0.255 area 0
Router(config-router)#network 172.16.70.0 0.0.0.255 area 0
Router(config-router)#
00:34:01: %OSPF-5-ADJCHG: Process 100, Nbr 172.16.60.1 on Serial3/0 from LOADING to FULL, Loading Done
Router(config-router)#network 172.16.70.0 0.0.0.255 area 0
Router(config-router)#network 172.16.80.0 0.0.0.255 area 0
Router(config-router)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]

Router 2

Tugas 4 Jarkom III - Setting Jaringan Summarization

Konfigurasi Router0:

Router>ena

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#int fa0/0

Router(config-if)#ip add 172.16.10.1 255.255.255.0

Router(config-if)#no sh

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit

Router(config)#int ser2/0

Router(config-if)#ip add 172.16.5.1 255.255.255.0

Router(config-if)#no sh

%LINK-5-CHANGED: Interface Serial2/0, changed state to down

Router(config-if)#clock rate 64000

Router(config-if)#exit

Router(config)#

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Router(config)#ip route 192.168.0.0 255.255.252.0 ser2/0

Router(config)#exit

%SYS-5-CONFIG_I: Configured from console by console

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#ip route 172.16.1.0 255.255.255.0 ser2/0

Router(config)#exit

%SYS-5-CONFIG_I: Configured from console by console

Router#copy ru

Router#copy running-config st

Router#copy running-config startup-config 

Destination filename [startup-config]? 

Building configuration...

[OK]

Konfigurasi Router1:

Router>ena

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#int fa0/0

Router(config-if)#ip add 172.16.1.1 255.255.255.0

Router(config-if)#no sh

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit

Router(config)#int ser2/0

Router(config-if)#ip add 172.16.5.2 255.255.255.0

Router(config-if)#no sh

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#exit

Router(config)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Router(config)#int ser3/0

Router(config-if)#ip add 192.168.1.1 255.255.255.0

Router(config-if)#no sh

%LINK-5-CHANGED: Interface Serial3/0, changed state to down

Router(config-if)#clock rate 64000

Router(config-if)#exit

Router(config)#

%LINK-5-CHANGED: Interface Serial3/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0, changed state to up

Router(config)#ip route 172.16.10.0 255.255.255.0 ser2/0

Router(config)#exit

%SYS-5-CONFIG_I: Configured from console by console

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#ip route 192.168.2.0 255.255.255.0 ser3/0

Router(config)#exit

%SYS-5-CONFIG_I: Configured from console by console

Router#

Konfigurasi Router2:

Router>ena

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#int fa0/0

Router(config-if)#ip add 192.168.2.1 255.255.255.0

Router(config-if)#no sh

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit

Router(config)#int ser2/0

Router(config-if)#ip add 192.168.1.2 255.255.255.0

Router(config-if)#no sh

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#exit

Router(config)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Router(config)#ip route 172.16.0.0 255.255.240.0 ser2/0

Router(config)#exit

%SYS-5-CONFIG_I: Configured from console by console

Router#

Setelah semua router sudah dikonfigurasi, setting IP address pada masing-masing PC

PC0

IP Address: 172.16.10.x  ("x" diisi angka terserah yang penting antara 2-254)

Subnet Mask: 255.255.255.0

Default Gateway: 172.16.10.1

PC1

IP Address: 172.16.1.x  ("x" diisi angka terserah yang penting antara 2-254)

Subnet Mask: 255.255.255.0

Default Gateway: 172.16.1.1

PC2

IP Address: 192.168.2.x  ("x" diisi angka terserah yang penting antara 2-254)

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.2.1

Terakhir cek ping ke IP address PC lain dengan Command Prompt.